Refine Your Search

Date

Date

Topic

Topic

Ferrous metals Suspension systems Coatings, colorants, and finishes Suppliers AGE-3 Aircraft Ground Support Equipment Committee Chassis Wheels

Search Results

Viewing 21 to 40 of 60
<< First< Previous123Next >Last >>
Sort by published
Standard

Aircraft Damage Caused by Ground Support Equipment
2009-12-09
HISTORICAL
AIR1589A
Only those incidents where a piece of ground support equipment directly associated with the "turnaround" servicing of an aircraft was involved are reviewed. Specifically excluded are those incidents that occurred during heavy maintenance, overhaul activity, or aircraft taxiing.
Standard

Aircraft Cargo Conveyor - Battery Powered
2008-10-20
HISTORICAL
ARP1836B
This SAE Aerospace Recommended Practice (ARP) outlines the functional and design requirements for a battery powered, self-propelled belt conveyor for handling baggage and cargo at aircraft bulk cargo holds. Additional considerations and requirements may legally apply in other countries. As an example, for operation in Europe (E.U. and E.F.T.A.), the applicable EN standards shall be complied with.
Standard

400 Hz Connection Aircraft Electrical Maintenance Procedures
2008-03-28
HISTORICAL
AIR4365A
This SAE Aerospace Information Report (AIR) describes field-level procedures to determine if 400 Hz electrical connections for external power may have been subjected to excessive wear, which may result in inadequate disengagement forces.
Standard

AIRCRAFT GROUND AIR CONDITIONING SERVICE CONNECTION
2005-07-11
HISTORICAL
AS4262A
This SAE Aerospace Standard (AS) defines interface configurations for the ground air conditioning service connection on commercial transport aircraft. In addition, it defines the clearances required to accommodate the connection of ground air conditioning hose couplings. Two types of service connections are included. The Type A connection (Figure 1) is a slotted ring with integral locking pads and is comparable to the MS33562 connection. The Type B connection (Figure 2) is a flanged tube with external locking lugs (Figure 3). The Type B connection has the same interface dimensional requirements as the Type A connection.
Standard

Nose Gear Towbarless Tow Vehicle Basic Test Requirements
2005-02-10
HISTORICAL
ARP5283
The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852A and ARP4853A. b Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, reduce the certified safe life limit of the nose gear, or induce a stability problem during pushback and/or maintenance towing operations. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only. It is not meant for dispatch (operational) towing (see definitions in Section 3). Dispatch towing imposes greater loads on nose gears and structure due to additional passenger, cargo, and fuel loads.
Standard

Design Specification for Regional Aircraft Towbarless Tow Vehicle for Pushback and/or Maintenance Towing Operations
2004-12-30
HISTORICAL
ARP5916
The tow vehicle should be designed for towbarless push-back and/or maintenance towing of regional type aircraft as specified in 1.3. The design will ensure that the unit will safely secure the aircraft nose landing gear within the coupling system for any operational mode. The purpose of this towing procedure is to achieve a safer and faster operation than is possible with conventional towing equipment.
Standard

400-CYCLE GROUND POWER UNIT PROVISIONS FOR AIRCRAFT ELECTRICAL SYSTEM PROTECTION
2002-12-16
CURRENT
ARP760
This SAE Recommended Practice which defines the terms and tabulates the limits of the characteristics for various protective devices used in conjunction with 400-cycle ground power for civil aircraft is intended to assist the airlines in standardizing on 400-cycle protective systems. The limits found to be acceptable in the civil aircraft industry are presented.
Standard

Baggage/Cargo Trailer Requirements
2002-07-16
HISTORICAL
ARP1348A
This SAE Aerospace Recommended Practice (ARP) applies to airline trailer equipment with four wheel running gear pulled and steered through an integral tow bar, for use on airport ramps and other airport areas for transporting baggage, freight, and other materials. This ARP can apply to any airline/airport trailer chassis regardless of its equipment; the trailer bed can be designed to carry either bulk baggage/cargo, or a cargo unit load device by means of a rollerized conveyor system, or a piece of aircraft servicing equipment (e.g., ground power unit, air start unit, etc.).
Standard

Commercial Aircraft Towbar Attach Fitting Interface
2001-10-01
HISTORICAL
AS1614B
Operators of commercial passenger and cargo aircraft in unanimity will request aircraft manufacturers to follow this standard in the design of the nose gear (when towing operations are normally done from the nose gear) in conventional tricycle type landing gears.
<< First< Previous123Next >Last >>
X